It happened to a family in Henderson last November: their furnace had sat idle since the previous February, they flipped it on for the first time as temps dropped into the 40s, and within an hour everyone had a dull headache they chalked up to allergies. A neighbor who happened to be an HVAC tech spotted a corroded flue pipe and called it what it was — a slow carbon monoxide leak. Furnaces that sit dormant through a 115°F Las Vegas summer and a hot, dusty monsoon season don't always come back to life cleanly. Before you rely on your heater for the next three or four months, there are a handful of checks every homeowner should understand.
Why Las Vegas Furnaces Face Unusual Stress
Most of the country runs their furnace steadily from October through April. Here, our heating season is compressed — roughly November through February — but the stress on equipment is disproportionate. Furnaces sit completely idle through summer temperatures that routinely exceed 110°F, which accelerates metal fatigue inside the heat exchanger. Dust storms during July and August pack debris into return vents and burner compartments. And our extreme hard water means any condensate-related components corrode faster than they would in a humid climate.
The result: a furnace in Summerlin or Centennial Hills may develop a cracked heat exchanger after fewer heating seasons than the same unit in a mild-climate city. That crack is the most direct path for combustion gases — including carbon monoxide — to mix with the air circulating through your home.
Understanding the Heat Exchanger and Why Cracks Matter
The heat exchanger is a metal chamber that separates combustion gases from the breathable air your blower pushes into living spaces. Flame burns inside it, heats the metal walls, and your household air flows around the outside of those walls — never actually touching the combustion gases. When the exchanger develops a crack, that separation fails.
Carbon monoxide (CO) is colorless and odorless, so there is no sensory warning when it begins entering your airstream. Even at low concentrations, prolonged exposure causes headaches, nausea, and confusion. At high concentrations, it is fatal. The Consumer Product Safety Commission consistently lists faulty heating equipment among the top causes of non-fire CO deaths in residential settings — which is why a visual and combustion-analysis inspection of the heat exchanger is a non-negotiable part of any professional HVAC maintenance plan.
Warning Signs You Should Never Ignore
Because CO itself is undetectable without instruments, you have to watch for indirect clues. Some of these are physical symptoms; others are equipment behaviors that point toward incomplete combustion or exhaust leaks.
- Flu-like symptoms that clear up when you leave the house — headaches, dizziness, or nausea that multiple household members experience simultaneously are a classic CO pattern.
- Yellow or orange burner flame — a properly tuned gas burner burns blue. Yellow or flickering orange indicates incomplete combustion, which produces more CO.
- Soot or black streaking near vents or registers — physical evidence that combustion byproducts are entering the air distribution system.
- Unusual smell when the furnace first starts — a burning-dust smell the first time you fire up is normal and clears quickly. A persistent acrid or chemical odor is not normal.
- CO detector alarm — treat it as a real emergency every single time, not a nuisance. Evacuate first, investigate second.
- Furnace short-cycling or shutting off unexpectedly — the rollout and limit switches in your furnace are designed to shut it down if combustion gases are going where they shouldn't. Frequent tripping means something is wrong.
- Excessive condensation on interior windows — can indicate combustion gases are increasing indoor humidity, a sign the venting system may not be exhausting properly.
CO Detector Placement: What Nevada Requires and What We Recommend
Nevada law requires CO alarms in any single-family home that has an attached garage or a fuel-burning appliance — which covers virtually every home in the Las Vegas metro with a gas furnace or water heater. The minimum requirement is one alarm outside each sleeping area, but for meaningful protection in a larger home, we recommend detectors on every habitable floor, including one in or near the furnace utility room if it is adjacent to living space.
A few practical notes: combination smoke/CO alarms are acceptable and convenient, but CO alarms have a finite service life — typically five to seven years. Check the manufacture date on the back of the unit, not just whether the test button responds. A detector whose sensor has aged out will not reliably catch a low-level leak. Replace units that are past their rated lifespan before this heating season gets underway.
What Our Combustion Check Actually Covers
When our technicians perform a furnace tune-up, the combustion analysis portion is more than a visual look. Here is what a thorough inspection includes:
Heat Exchanger Inspection
We use a combustion analyzer and in many cases a camera inspection to check for cracks, pinholes, or corrosion in the heat exchanger. A cracked exchanger almost always means the furnace should be replaced — there is no safe field repair for this component. If we find one, we will show you the evidence and walk you through your replacement options and the associated costs so you can make an informed decision.
Flue and Venting Verification
We check that exhaust gases are actually exiting the building — not back-drafting into the living space. This includes inspecting the flue pipe for corrosion, disconnected sections, or blockages (birds and rodents occasionally nest in unused flues over summer).
Burner Combustion Analysis
Using a calibrated analyzer, we measure CO in the flue gases and confirm that the air-to-fuel ratio is within the manufacturer's specified range. An out-of-spec ratio increases CO output at the burner level and stresses the heat exchanger further.
Filter, Blower, and Airflow Check
Restricted airflow is one of the leading causes of heat exchanger stress. A severely clogged filter or failed blower forces the exchanger to run hotter than it was designed for, accelerating crack formation over time.
When to Call a Professional
If your CO detector sounds, do not reset it and go back to sleep — get everyone out of the house, leave the door open, and call 911 from outside. Once emergency services have cleared the building, then call an HVAC company. If your detector is not sounding but you are experiencing symptoms, yellow flames, soot near registers, or a furnace that keeps shutting itself off, those are reasons to have a professional inspect your system before you run it again. These are not issues that benefit from a wait-and-see approach.
Our technicians carry combustion analyzers on every service call and perform the full heat exchanger and venting inspection as part of our tune-up visit. If we find a cracked exchanger or a hazardous condition, we will document it clearly and give you honest options — including replacement systems ranging from around $7,900 for a 2-ton installation up to $14,500 for a 5-ton system, with financing available from $129/month for qualified customers. To schedule a combustion safety inspection or get a fast quote, call us at (702) 830-7116 or use our 60-second instant quote form — NV License #0072282.